I have always called the little strips of fabric that we use for starting and stoping, caterpillers. In the beginning, when I just starting to chain stitch, I had no idea they even had a name, so I just gave them a name, for what they looked like to me.

Dawn
In beautiful Northwest Montana

BONNIE HUNTER calls the little fabrics LEADERS AND ENDERS... she talks about it in her books. She actually does other units for her scrap quilts using them as LEADERS AND ENDERS.

I usually do the 2 squares sewn on the diagonals then cut into two units.

When I do sew individually cut triangles I make sure they are starched so stiff they can stand up. That helps avoid the tip going into the machine. I also use point trimmers to trim the tips before I sew them.



.

Bev--Funny how I didn't think of the difference of triangles, with or without, the bunny ears. I have used the Omnigrid triangle rulers almost from my first quilting days ans if I am caught with triangles with the bunny ears it is definitely "off with the ears" before I consider sewing.

Another way to prevent the corner being "eaten" is to cut them off (like take off the bunny ears before you sew the half squares together. Just trim off a 1/4" at right angles to the straight edge-same as if you are using the "Easy Angle" ruler to cut them). I also saw somewhere that if you end with your needle down, your feed dogs are also at lowest point and it is easier to slide the new piece under the pressure foot! Have fun-you should have been in the Traveling HTS's swap-lots of experience sewing those little buggers! Bev

Hi Ron, I just looked at your profile quilts! Holy Cow! those are some beautiful quilts. You certainly seem to have conquered many of the technical issues we all struggle with, like sewing bias. That star rhapsody quilt is simply gorgeous. Thanks for posting some of your quilts.

Kathy

Thank you all! It's amazing what I am learning. I've never heard of a straight stitch throat plate! I doubt I have one so will order one. Also, given the other suggestions I can't wait to get home tonight to get back to the machine. Thanks against to everyone for taking the time to help me out.

Ron

Definitely consider in investing in a single hole "straight stitch" throat plate. Not only will is help in this situation, but it is also ideal for free-motion quilting.

One thing you might do until you get the throat plate is to not start at the point. I try to start my triangle pieces at the place where the seam allowance is. This may mean you have to lift the pressure foot as you start each patch (the knee lifter really helps here) but by placing the patch at the seam line instead of the point helps the feed dogs feed the patch through better.

OK, I think maybe if you use a straight stitch plate and foot it will help; but, you do need to hold on the the ones that have already gone thru. The other thing that might be the problem is--new needle--if your needle is dull it can cause those kinds of problems.

A straight-stitch plate definitely helps a lot. My machine has a 'stitch-lock' so you can't accidently change your stitch or needle position with the straight stitch plate on there. But if your machine doesn't have that, you could always put a brightly colored sticky note near any needle or stitch positioning buttons/levers/etc to remind you to not do that.
"Gonads" - heh heh... I like it... I usually just call my "starter and stopper" pieces of fabric "where the heck did that thing go?" Maybe I need something more creative?
-Tina

speeding is subject to a "speeding violation". Slowing down particularly when feeding in the hst's is a good idea.
The straight stitch plate helps a lot because the fabric has now where to go.

Teri

Ron114 wrote:
When I had this problem I learned to hold onto the previous piece behind the presser foot, giving it a slight tug, as I was sewing the next piece until it cleared the point. Most of the time when I'm sewing triangles now I'm sewing on paper and the machine I'm using now doesn't give me as much trouble. I don't have a straight stitch plate although I'm sure that would help. I would be afraid that I would change the needle position and end up with a broken needle.

Oh dear! I'm afraid proper folk like Jean Wells call them "Bunny Tails", but my mom prefers the scientific/latin and refers to those starters and stoppers as 'gonads'. We're pretty scientific at my house too...

For what it is worth--I do all my piecing with the straight stitch foot and plate. Amazing how far fewer pieces get eaten at the beginning compared to using the zig zag foot and plate. Of course, machines differ so this may not be useful information. I always also use stoppers and starters but like as not they are just another project, sitting at the machine for that precise purpose.

I use a real work horse machine, Singer Professional, so I have no special features like needle up/down or whatever. Also I have to physically change the feed dogs and plate, undoing four small screws but it is worth the effort for me even if on occasion I lose a screw.

Thanks for responding so quickly, Teri and Margo!!! Why aren't you watching the Oscars? Or, maybe you are! This is very helpful, but I think I'm just being dense - I've been using a scrap to get started and when I end the chain. But, this happens in the middle of the chain. I'll get a run of several good ones, then all of a sudden Wham!!! the triangle gets stuck. It's almost like either the feed dogs don't catch or the points get caught under the plate. Maybe I'm going too fast? Thanks again. Ron